Car Key Button Repair
A damaged car key button is frustrating. You might need to call an emergency locksmith service that is available 24 hours a day for assistance or to purchase a new remote.
But, you may be saving money by repairing an old key fob rather than replacing it. This is particularly true if the problem is due to the worn-out switch or defective contact.
Battery
If the buttons on your key fob are not responding to your pressing them, it could indicate that the battery has failed or is close to the end of life. It's simple to replace the battery yourself instead of paying a locksmith or dealership.
First, locate the battery compartment. The battery compartment is usually located on the back of the key fob and may be hidden behind a cover which opens or an open button that opens the access point. After the compartment is opened then look for the small button-cell battery. It's usually the shape of an ordinary coin and is identified with a plus and minus symbol. Remove the battery that is old and replace it with a brand new one. Make car key repair service that the plus and the minus symbols are properly aligned.
Close the compartment and snap the two halves of your key fob. Before closing web page make sure to align and snap the components into place. To verify whether the buttons function properly you can press any one of them.
If your remote key fob ceases working after replacing the battery, it may be experiencing other issues that require a different kind of repair. Dropping the fob into a pool of water can cause it to stop functioning. It could also be experiencing an internal electrical failure or may need to be deprogrammed by a dealer or locksmith. Find out what's wrong with your key fob applying these other typical automotive troubleshooting methods.
Switches
There are a variety of switches used in the car key fob according to the year and model. The older style keys have an embedded chip that can be seen inside the case. The latest keys operate by sending signals to your car. The buttons on a key may be damaged or worn out through regular use, irrespective of the model. As a result, they become difficult to press or even unresponsive. If you try to press the button too hard the button, it could cause damage, and could even prevent the key from starting your vehicle in the future.
If you're unable to get your key to work, try changing the batteries. If that doesn't help, you may need to clean the key's fob and re-adjust the switches. These tiny electronic switches are more prone than larger components of the key to break due to the fact that they are constantly tossed around.
The switches have a rubbery feeling and are coated with an electrical conductor. The film may wear off over time. However, they're tiny and inexpensive to replace. They're soldered to the circuit board, therefore you need to carefully take them off without damaging anything else. Then, you can solder in the new ones and reassemble your key fob.
A good way to keep your car key fob from becoming damaged is to avoid using it for longer than a couple of hours at a stretch, and also to not leave it in areas that it will be visible. If you're not using your key, put it away in a secure place.
If the issue continues to persist after you've cleaned your key fob, replaced the battery and tried to clean it, then you may need to consult a locksmith. A professional locksmith can check the frequency of your key to determine if your vehicle is still capable of communicating. They can also open and replace microswitches as well as change cases, and more.
Outer Case
A key fob spends many hours bouncing around, and when the buttons aren't allowed to move between the case they can get stuck or broken. If changing the battery or cleaning it with an alcohol-based swab and a cotton pad rubbing alcohol don't resolve the issue, then removing the case and checking it out could be required. If the contact points where the buttons touch aren't fitting well or are worn out, adjusting them might be the only solution to fix the issue.
Some keys are equipped with buttons made of rubber that wear away over time. The rubber stretches and nails pierce it and the buttons can become difficult to press. In this case the key may fail and it's time to replace the case or the buttons. This repair involves disassembling the remote, locating the buttons on the circuit board, heating up the solder and carefully remove them. The circuit board then gets soldered with new buttons. The case can be rebuilt and the horseshoe key blade can be attached. The new buttons must be a close fit into the case to prevent them from falling out.
Inner Case
Over time, your key fob's buttons can be damaged or stuck because of the continuous rubbing and accidental pressing. If your key fob ceases to function while you are away from home It is possible to fix the issue fast by using metallic tape and punch holes. This will allow you to open doors, but not start the car. This quick fix may allow you to safely return to your vehicle to finish your trip.